This is a range of high quality tungsten carbide tipped saw blades which will produce outstanding results on circular sawbenches and mitre saws. As with all CMT products these blades are made to the highest standards of design and manufacture with only the best quality materials being used throughout.
They are offered in six different types, coarse tooth pitch for ripping, medium for general purpose work, fine and extra fine for precise and accurate crosscutting, trapezoidal or triple chip for clean cutting of plywood and a 40° alternate bevel design for the ultimate finish on faced boards. The correct choice of blade for a particular job is important if best results are to be achieved and we are confident that the range offered here should be sufficient to cover all sawing applications, from rough timber preparation to finish cutting of veneered boards.
All blades are provided with a 30mm diameter mounting hole plus provision for two different pin hole arrangements where required. We stock a range of spacers to adapt the blade bore to diameters less than 30mm. Please request the correct spacer when ordering.

A range of coarse pitch blades suitable for rip cutting (with the grain) on saw benches only. The large gullet between the teeth accepts larger chips and thus permits higher feed rates. Laser cut expansion slots prevent distortion when hot. For use where feed speed is more important than quality of cut.

Excellent speed and efficiency with 15° hook angle and a medium number of teeth. Whether ripping or crosscutting these blades will work with a wide range of materials, like hard/soft woods and plywood with accuracy and efficiency. A must for professional woodworkers.

General purpose rip/crosscut negative rake -5° hook angle also available (701238 below)

Designed to guarantee high performance on most industrial sawing machines, these blades are ideal for cutting all types of materials such as hard and soft woods, plywood, chipboard and MDF. The alternate grind and the expansion slots made by laser as well as the high number of teeth make these blades a tool of sure success for a perfect finish on all projects.

Alternate straight and trapezoidal, or double chamfered, teeth with a fine pitch make this the preferred blade for plywood, particle board and melamine-faced board on both sawbenches and mitre saws. The chamfered teeth cut out the centre of the groove and the flat top teeth follow behind to clear out the sides of the groove.

The all-round cut off blade for hardwood, softwood, plywood, chipboard and MDF. The alternate top bevel teeth, 10° or 15° hook angle and high tooth count make these blades perfect for use on all professional machines. With the ultimate fishhook expansion design the blades run smoother and work more efficiently.

This is the blade for the ultimate fine finish on all sorts of timber. The sharply bevelled teeth cut the material with a shearing action alternately left and right to give the best possible finish to the work. Ideal for use on either sawbenches and mitre saws for fine crosscutting of solid timber, plywood, faced boards and double-sided melamine.

A range of fine cut negative rake blades which are designed for cutting thin hollow sections in non-ferrous metals such as aluminium tubes and extrusions. The 6° negative rake angle gives a good finish as well as preventing collapse of the section. These blades also have an application on radial arm saws where the negative rake angle can prevent the blade “climbing” over the work.

The scoring saw is an optional fitting on several sawbenches, particularly those designed for cutting sheet material. The blade is fitted a short distance in front of the main blade and cuts a shallow groove on the underside of the board, preventing splintering on faced and veneered boards. The scoring blade shown here is of the adjustable type and comes in two parts with a set of shims so that the cut can be aligned exactly with that of the main blade. The diameter of the blade is 100mm and the range of adjustment is from 2.8 to 3.6mm. The bore diameter is 20mm.

The ultimate in finish blades! CMT puts a 40° top tooth angle on its blades to provide flawless finishing on single and double laminates, melamine, hard and soft wood - this means absolutely minimal chipping on double faced material! The use of melamine and fine cut off is excellent on large mitre saws for complex angle cuts where accuracy is a must. Use on table or wall saws without the need of the scoring blade.